Friday, November 12, 2010

Cristian's MR-03 at the Worlds



Brief post, cause it's late... :P This was my car at the Worlds. It was fantastic. It allowed me to finish 3rd Overall in GT Mod amidst some very stiff competition and without having driven a Mini-Z since June. It had prototype parts on it as well as some other parts that I had personally not run on an MR-03. One of them was the Low Profile Suspension. I LIKE IT A LOT! Come to think of it, our results seem even better when we put the conditions into perspective. In every class, we had the Top Finishing MR-03's as well.

My set-up was simple:
Front:
-Silver Low Profile Springs
-4 Degrees of Caster
-Low Down Knuckles 0.3 shim underneath/ 0.5 above knuckle (below ball)/ 0.3 shim at the top to give slight Pre-Load
-30000 Wt Kyosho grease on the lower ball (where the spring insets)
-1 Degree Camber
-PN RXF 15 Tires, on 20mm Wheels, trued to 23mm on +2 Wheels

Rear:
-Reflex Soft MM T Bar
-96mm Position on Motor Mount
-Silver Side Springs on Tri Shock, 15000 wt Grease
-450 CST oil inside Kyosho Oil Shock, 50% Rebound
-Kyosho Yellow Spring, Pre Load set to have chassis level when fully loaded
-PN Racing 6 Degree Slicks, Trued Flat. +3 Rear 20mm Wheel
-Atomic Diffusor Installed

Power:
-CTP Tuned 32 Turn PN Spec Motor
-Atomic VP 800 Batteries
-Gear 11/53





Thursday, September 30, 2010

WINGS!!!








Pictures, 'nuff said!

Sunday, September 26, 2010

Low Profile Front Suspension Set-Up






Hi guys! Check out the pics!!! This is a little project that we kept kind of hush until we really knew it would work. Basically what it is, it is a 12th scale pan car-style front suspension spring set. The Springs are small units that were designed to fit inside the lower pivot ball of your MR-03 Front End. In order to make it PN Racing Front Lower-Arm compatible, we made the lower ball narrower. So this way, you can have a reverse-king pin set-up and you can also run 4 degrees of caster with our front end!!!

These parts were not really designed to replace our extra-long King Pin Set-up, but rather they are an option, in case you want to run reverse-type king pins. WE ARE STILL PRODUCING THE EXTRA LONG KING PINS AND ANCILLARY PARTS.

This new front end requires you to run some pretty small diameter front tires so that the front does not sit too high and it is also a bit harder to adjust. You just can't add washers on the fly to set pre-load. Up Travel is also not really adjustable, but with the coils compressing quicker, the suspension travel is less than with the Extra Long King-Pin Set-Up.

This set-up works really well and reduces the slop in the front end even further. There are limitations related to ride-height in the front and it is a bit of a pita to change the front springs in order to adjust properly, but when tuned right it can offer more precise handling (due to the reduced slop), and it is lighter in weight. It will be offered as a complete package: King Pins, 4 delrin Balls, E-clips (with a couple of spares) and a soft/med/hard spring set. it should sell for around 14 bucks!!!

If you are concerned about the bottom hitting, don't worry, the bottom of the kingpin is at the same position as the bottom of the reverse King Pin PN Racing set-up!!!

Tuesday, August 31, 2010

Reflex flight 910 preparing for takeoff...
















Check back tomorrow for updates!
Yes, really tomorrow. I already have the pics... :p
updated 9/1/10. more tomorrow...
updated 9/2/10. every day, new pics...
updated 9/3/10. F430 fitment...
updated 9/4/10. McLaren F1 fitment...
updated 9/5/10. SC430 fitment...
updated 9/6/10. DB9R fitment...
updated 9/7/10. NSX GT fitment...
updated 9/8/10. I was going to take pics for 350Z fitment, but I the original mold is being replicated...
updated 9/9/10. Hope to have images of the production molds tomorrow...
updated 9/10/10. So flight 910 is a little delayed getting out of the gate, but I dropped off the lexan today at our production shop. Production molds will be done early next week, and we should have production units ready for sale the week after! Stay tuned!
updated 9/16/10. First samples off mold!!! WOOT!
updated 9/21/10. We danced back, and now IT'S ON!

Thursday, July 22, 2010

Our Tri-Shock

Pictures right now, It's late and I'm real tired... I'll elaborate soon!



Monday, July 5, 2010

The Future is Here ;)

With the arrival of the MR-03, the development of this platform has rapidly changed the world of Mini-Z. These machines are now more precise, easier to drive, handle more power and are overall better cars.

The latest incarnation of my personal set-up led to the development of a lighter tri-shock suspension with proper suspension angles. The tri shock allows for easier tweak adjustments (so the car turns equally left to right) and provides better acceleration. Note that our tri-shock set-up uses ONLY the side shocks and a center shock. When using this suspension with disk dampers, the car becomes over dampened, and the advantages of having independent side to side and fore and aft suspension are eliminated.

Below we also have the adjustable upper arm mount. This is truly a revolution. It is designe to be used with any suspension type and/or upper arms, but it works best with our king pin set-up because we can incorporate proper caster angles. 0-2 degrees of caster is really inadecuate for onroad cars. The happy point lies somewhere between 3 and 6 degrees, many times up to 8. This is why all larger scale 2WD race cars use this much. YOU WILL NEVER SEE A CAR RUNNING 0 DEGREES, and very little, if any, less than 4. Another advantage is working with your roll centers. I wrote a whole article about this before, but with a front upper arm mount, you can adjust the roll center in my favorite way, by raising the inner pivot of the A-Arms. Lastly, you can adjust your camber angle so your tires wear evenly under all kinds of different track conditions.

The last thing that is amazing is the weight of the cars. I have had to add about 6 grams of balast to the bottom of the chassis to get to a racing weight of 175.8 grams. This is with a FULLY HOPPED-UP Car, WITH A FRONT BUMPER ON IT!!! This was unheard of with the MR-02's. Balasting is a good thing though, it allows you to play around with the weight of the car and locate it in the most effective spots for your car balance to be as close to perfection as is possible.

Hope you enjoy the pictures! CT




Saturday, June 19, 2010

Reflex Racing Special Project: the little Mini that could...





1/14/09

PN says: Do you plan to go to KO race in March?

Joe says: Yup

PN says: Maybe I will build a 90mm AWD for the Mini Sport Class

Joe says: AWD 90mm?

PN says: KO race will have a Mini Sport Class for 90mm cars only

Joe says: Ah awesome! I should do that too

PN says: 2WD or AWD? They are running them together

Joe says: I have a Mini Cooper MR-02 right now

Joe says: Turns so quick, but traction rolls

Joe says: I need to try and fit a sway bar on it

PN says: Yes maybe you need a harder front tire

Joe says: I think I’ve got 25’s on it!

PN says: You should try 30. Or stock tire

Joe says: Yah I guess so

blahblahblah...


And that's how it started.

We all knew that Philip would never leave his beloved MR-02 chassis for the AWD...

Missing my old 1:1, I had built up a Mini Cooper MR-02 using PN narrow front end just to goof around with.


2/25/09

PN says: 90mm motor mount sample is here

PN says: I just assembled it. Sooooooooooo sweet

PN says: I can’t wait to try

Joe says: *&$% it! Send me a pic

Joe says: Maybe I’ll try to sneak out of work to pick it up.


And just like that, the PN 90mm MM MR-02 motor mount was born. I couldn't sneak out of the office in time to pick up the test sample, so I had Philip send it to me. I rebuilt my 2WD Stock MR-02 with all the new Mini chassis components just in time to MISS the last day that Kenon would ever be open. For some reason, I didn't understand what Philip meant by "I'm closing the track today." I just thought, "Yeah I know. I'll try to stop back by tomorrow for some testing..."


3/2/09

PN says: I tested the motor mount today. The setup is GOOD!

PN says: I beat Chad in stock class at last Friday

Joe says: hahahaha

Joe says: awesome

Joe says: what spring

Joe says: are you running wide tires?

PN says: on my track, front yellow

PN says: F40 body

PN says: yes

PN says: 1 front, 0 rear

Joe says: yah i'm going to run mini cooper

PN says: another choice is AE86

PN says: also very good and stable

Joe says: yah

PN says: when i put on the F40, sooooooooooooo good

PN says: huge difference

PN says: wide rear tire

PN says: i also used an F1 shock on top, much better

Joe says: interesting

Joe says: i never liked the f1 shock

Joe says: prefer the oil shock

Joe says: but may be too high for this setup

PN Philip says: oil shock is too big, try the f1

PN Philip says: i can set you up

Joe says: i don't care i'm still running mini cooper

Joe says: will be fun


Sure I had committed to running the Mini Cooper body, but I still had a few tricks up my sleeve. I decided to abandon the front swaybar attempt since there was just no room in the chassis for any of the conventional setups. First thing I did was lighten up the body. The "sunroof" mod is popular with racers, and remains legal in most classes. It usually results in a few 0.1g from the top of the car. The funny thing about the mini cooper body is that the roof is only glued to the windows and has no other attachment points to the body. This makes it very easy to remove and thin out with a dremel and wire brush attachment. I would be running an MR-02 chassis with the PN MR-0175 tower bars to reduce the roll with this already tippy setup.


The other big upgrade would be the rear wheels and tires. I've experimented with semi-wide (9.5mm) rear tires in stock class before with some success. I find that in certain traction/temperature situations, they work as well as full wide rear tires. I had some sample semi-wide SSG's laying around, and I knew that these would be just the ticket. The standard 8.5mm narrow wheel/tire setup leaves room in the Mini Cooper wheelwell, so I knew we had some space to play with. Simple math said that 9.5mm semi-wide tires on a -1mm offset semi-wide wheels would give me the same rear track width as the standard 8.5mm narrow setup.


So where do you get -1mm semi-wide wheels? You make them! Starting with Atomic -1mm wide wheels, I carefully sanded them down to the correct width and glued up the semi-wide SSGs. Why all this trouble for wider wheels and tires? Well first of all, we would be running PN 70T stock motors which have more than enough grunt with race batteries to overpower narrow rear tires. The smaller contact patch of narrow rear tires not only affects the power application, but the consistency of the handling via squirm. I thought that a narrow aspect ratio (unless trued WAY down) might squirm badly under the combination of acceleration and cornering loads on exit. At this point, I hadn't figured out whether the chatter/traction rolling in my previous setup was generated from the front or the rear of the chassis. I suspected a little bit of both - sometimes the nose would tuck in corner entry, sometimes the rear would hop around on exit. I hoped that the semi-wide rear tires would give me a more consistent and stable rear contact patch to apply power during corner exit and solve 1/2 of the problem.


Just for good measure I also sanded some Atomic +1 narrow wheels down to 8mm width for use in the front. With camber, they had no issues rubbing, and I thought they might help in the front end stability department...


Took the new setup + a few options out to OC/RC to shake her down. Better than before (due to the damper plate system), but I was STILL traction rolling when the tires got up to temperature and if I started pushing it. I tried going stiffer on the suspension, damping, etc. to control the oscillation, but no help. The car did feel very consistent when I backed the pace off to 80%, and the thing could turn on a DIME. It was very interesting being able to run so deep into a corner, stay wide, turn in late and not wash out and blow the apex. On top of that, the car could actually tighten the line on exit under power. This would come in handy a little later...


Race Day!


After a long drive up to NorCal, we got set up in the mall area. This was my first mall race and Binh and the Inside Line crew really put together an awesome venue! There was an escalator leading to the second floor where spectators could gather for a bird’s eye view of the racing action below. Practice was VERY crowded with a line 20-30 racers long waiting to get their shot on track in timed intervals. I knew my F1 car was fine, and I really wasn’t that concerned about Stock 2WD, so I focused on the Mini. As usual the track started off very green and slippery which brought the push out of most cars.


Some of you may wonder what those stupid pink flowers are all about. I always like to grab a random memento at each big race. In our rush, I hadn’t packed a pit towel or napkins or anything to wipe down the tires after gluing. We happened to be pitted next to this plastic flower bush, and the mall kindly “donated” some flowers so I could wipe the excess CA off the sidewalls (critical on the Mini fronts). I found the flowers in my pitbox a week later and there you have it.


I started out with semi-wide SSG’s on the rear with -1 offset Atomic wheels that I had shaved down. They provided plenty of forward traction, but I was struggling with finding the correct front tire for balance. I tried a variety of different tires from sticky to hard, and fiddled with the dual rate to dial in the steering. As the grip came up, traction rolling started rearing its ugly head. I ended up having to lift before the sweeper and bend it in to prevent the little Mini from flipping off the track. I miscalculated this more than a few times resulting in some pretty spectacular crashes much to the delight of the crowd that had gathered above. Lots of oohs and aahs and groans from the onlookers didn’t do a lot for my confidence. It felt like everyone in the mall was watching my little red cannonball careen off the track…


Come the qualifiers I really focused on blocking out the crowd and getting some solid conservative runs in. I managed to save a few of the traction rolls with some rather entertaining bicycles in the sweeper and the infield. This brought a smile to my face, and I really started having fun. I ended up qualifying at the rear of the grid in 9th, but I was confident that if I could keep it on all 4, I could fight my way into the top 5 for the main. I was the ONLY Mini Cooper in the field surrounded by F40’s, RX-7s, and other low slung coupes. While the top-heavy Mini had its issues, I was able to turn under just about anyone on exit, as long as the car didn’t end up on its lid.


For the main, I rolled the dice and tried a trued PN 20 degree front tire – stickier than I had been running in qualifying. I dropped my dual rate down and tested the front into the sweeper on the warm up laps. My hunch had paid off! Reducing the steering angle had all but eliminated the traction rolling! It wouldn’t hold up to a Scandinavian flick, but I could finally bend the little Mini into the sweeper at speed. I still had plenty of steering in the infield, and the reduced steering scrub had totally freed up the car for some pretty amazing corner speed.


When the horn sounded, I rolled into the throttle anticipating a pile up in the first corner. Looking for a gap, I ended up getting knocked backwards by a more enthusiastic driver, so I had a lot of work to do. In dead last, I settled down and just tried to nail the same line lap after lap while adjusting to the new steering characteristic. A few laps into the race, the tires came up to full temperature, and I finally got a feel for what I could get away in each corner. By that time I had started reeling in the other drivers. This is where it got exciting. I would pressure for a few corners, wait for a little mistake and duck right underneath. It felt like I was passing someone almost every other lap. When I came up on another driver coming onto the straightaway, I took an outside line in the sweeper just to be safe. Imagine my surprise when the little Mini slingshotted the long way around and completed the pass going into turn 1! The car was so on edge, but if I did my part, I could put it anywhere on the track. Given my tendency as a race announcer, I started providing my own color commentary from the drivers stand infused with plenty of laughter and disbelief as the Mini clawed it’s way through the field.


Being lost so deep in the field, the announcer hadn’t noticed my rise through the running order, but the cheers of the crowd above and my fellow racers in the pits brought to light that I was now sitting in 3rd place! I was stalking 2nd place who was running an excellent tight line. I got the drive coming out of turn 1 and the earlier outside pass in the sweeper made me think I could at least stay on the high line into the tight infield. I was as surprised as anyone when the little Mini carved a beautiful line around the outside and ahead into the chicane. From there, I pulled away in to a solid 2nd position. Up in front Philip’s F40 was gone. His car was turning almost the same laptimes as Stock 2WD. While I couldn’t manage to track down the win, I had just driven one of the best races of my life, grinning and laughing the whole way to 2nd place. From the cheers in the crowd and the celebration in the pits afterward, it felt like a win.


I can’t lie and say that the Mini never traction rolled during the main. I got a little aggressive on the exit of turn 2 and managed to tumble into the chicane, beaching the Mini on the rail. The car was literally high centered in the worst spot on the track for a marshal to get to. My buddy Emu had run into some mechanical trouble with his F40 (which was also ballistically fast), so he was laps down on the field. He had just come around the sweeper when he saw where my car was, rounded turn 2, made a beeline for me in the chicane and plowed full throttle into the rail I was on top of. The result? He could have broken my t-plate. He could have bent my axle. He could have broken his car. He could have flipped me on my lid. None of those things happened. The impact popped the little Mini off the rail onto the other side, landing on its wheels and I was back on course costing only a couple seconds for my mistake! A completely intentional, unselfish gamble by Emu had easily saved me a lap so I could continue mowing down the field. To this day, I still can’t figure out how he managed to spot my car, recognize it, weigh the risks of his track position and mine, formulate his harebrained scheme, and execute it against all instincts (it’s completely unnatural to intentionally drive straight into a rail) – all in about 1 second. It’s things like that that you never forget. Even at a toy car race.